x
I
n
k
a
r
p
BWB XP Flame Photometer
BWB XP Flame Photometer
Distributor & Service Provider In India
Inkarp Instruments, a trusted BWB Technologies partner, presents the BWB XP Flame Photometer in India, a cutting-edge instrument for elemental analysis.
Ready to use straight out of the box!
General Purpose Flame Photometer!
- Simultaneous detection and display of all 5 atoms of interest
- Intuitive user interface for true ease of use
- Display prompts step by step operation
- Built-in air compressor
- Solutions and labware included
- Data sharing via pc link via usb
- Operator independent determination of results
- 5 user selectable units of measure
- User selectable decimal places
- Integrated printer option uses readily available paper
- IQ, OQ, PQ web-based certification available: iq oq pq is completely unique in the analytical instrumentation arena. Available in english, russian, german, mandarin, french and spanish.More languages in development
- Correction of ca for the interference from high levels
Of NA
| Sample rate | 2 – 3.5ml/min | ||||
|---|---|---|---|---|---|
| Tubing materials | Silicone and Tygon® | ||||
| Required desk space for Instrument | 50cm (H) x 45cm (W) x 45cm (D)* For Safety reasons the Flame photometer requires 1m of unobstructed space above to allow dissipation of heat from the chimney. |
||||
| Instrument size | XP Flame Photometer 51cm (H) x 39cm (W) x 35cm (D) (20in x 15in x 14in) |
||||
| Shipping | 65cm (H) x 49cm (W) x 43cm (D) (25in x 19in x 17in) |
||||
| Weight | XP Flame Photometer – 14kg (30.8lbs) Shipping – 25kg (55.1 lbs) |
||||
| Optimal | Single point calibration Na 0.1 – 60ppm K 0.05 – 100ppm Li 0.05 – 50ppm Ca 1.0 – 100ppm Ba 1.6 – 100ppm Multi Point Calibration Na 0.1 – 1000ppm K 0.05 – 1000ppm Li 0.05 – 1000ppm Ca 1.0 – 1000ppm Ba 5.0 – 3000ppm |
||||
| Reproducibility | 1% Coefficient of variability for 20 consecutive samples over ten minutes at concentrations of 100ppm or less. (After instrument stabilisation). | ||||
| Specificity | Na/K/Li = <1% to each other when equal in concentration at <100ppm | ||||
| Limit of detection (LOD) and limit of quantification (LOQ) |
|
||||
| Time to stability | Less than 15 seconds after sample is introduced into the flame. | ||||
| Ions measured | Simultaneous measurement of Na, K, Li, Ca, Ba | ||||
| Interfaces | USB 0-2.5 volt output (based on sample concentration linked to element of users choice) Optional 4-20mA output in place of the above Optional integrated printer .csv and .pdf generated reports and files via FP-PC software |
||||
| Recommended minimum warm up time based on ambient temperature | 21ºC – 25 minutes | ||||
| Power requirements | 100V – 250V AC at 50 or 60Hz automatically selecting | ||||
| Reproducibility | 1% Coefficient of variability for 20 consecutive samples over ten minutes at concentrations of 100ppm or less. (After instrument stabilisation). | ||||
| Fuel requirement | Propane, Butane or Natural Gas* regulated to 19Bar. Flow rate of 0.4l/min | ||||
| Fuel requirement | Propane, Butane or Natural Gas* regulated to 19Bar. Flow rate of 0.4l/min *with modifications. BWB Technologies recommends either Propane or Butane for optimum results. |
||||
| Readout | LCD, four line, alpha numeric, back lit. |